輕鋼外殼的優點

Advantages of Light Steel Enclosures

　　（1）材質輕薄，保持面積大

(1) Lightweight material, maintaining a large area

　　傳統的房屋建造方法需要較厚的墻壁來支撐房屋。 因此，墻必須達到約20-25厘米，單個承重墻甚必須達到30厘米。這直接導致房屋可用面積的減少和功能的缺失。但是，輕鋼結構房屋可以解決此問題。由于材料輕而薄，因此房屋的墻壁不需要厚。平均厚度為14cm-20cm，住房率可達90％以上。

The traditional method of building houses requires thicker walls to support them. Therefore, the wall must reach approximately 20-25 centimeters, and a single load-bearing wall must even reach 30 centimeters. This directly leads to a reduction in the available area of the house and a lack of functionality. However, light steel structure houses can perfectly solve this problem. Due to the light and thin material, the walls of the house do not need to be thick. The average thickness is 14cm-20cm, and the housing rate can reach over 90%.

　　（2）施工工藝簡單，成本低

(2) Simple construction technology and low cost

　　傳統的房屋建造方法需要很長時間，并且會受到天氣的嚴重影響。如果天氣不好，施工時間可能會延遲。同時，對工人的技術要求比較嚴格，他們必須是熟練的工人才能完成施工任務。 輕鋼結構房屋的施工過程簡單，采用全天候施工方式，不受環境和天氣的影響。 它可以在一年中的任何時間建造。一般建設期可在1-2個月內完成。

The traditional method of building houses takes a long time and is severely affected by the weather. If the weather is bad, the construction time may be delayed. At the same time, the technical requirements for workers are relatively strict, and they must be skilled workers to complete construction tasks. The construction process of light steel structure houses is simple and adopts an all-weather construction method, which is not affected by the environment and weather. It can be built at any time of the year. The general construction period can be completed within 1-2 months.

　　（3）這些材料可以回收利用并且是的

(3) These materials can be recycled and environmentally friendly

　　傳統房屋拆除后，如果產生大量建筑垃圾，必須將其存放在專用停車場內，否則會造成嚴重的環境污染。輕鋼房屋的材料均為新型輕鋼，基本上采用出廠標準的標準件。施工期間采用的新施工方法（預組裝，干式作業）可以完全拆除并再次使用。90％以上可以重復使用。

After the demolition of traditional houses, if a large amount of construction waste is generated, it must be stored in a dedicated parking lot, otherwise it will cause serious environmental pollution. The materials for light steel houses are all new types of light steel, and basically use factory standard components. The new construction methods used during the construction period (pre assembly, dry operation) can be completely dismantled and reused. More than 90% can be reused.

以上是關于 濟南輕型鋼結構 的介紹，若想了解相關知識可請點擊：//4216.com.cn 我們將會全心全意為您提供滿分服務，歡迎您的來電！

The above is an introduction to Jinan Rolling Shutter Door Factory. If you want to learn more about related knowledge, please click: //4216.com.cn We will wholeheartedly provide you with full score service. Welcome to call us!